BestHard SS115
Surface hardener, dustproof compound for concrete.
Advantages:
Pre-mixed, one-component, no further mixing required, easy to use.
High penetration, strong activity.
Significantly increases hardness, abrasion resistance, prevents dust generation on concrete surfaces.
Enhances cleaning ability and prevents contamination of concrete surfaces.
Colorless, odorless, does not alter the color of the concrete surface.
Suitable for indoor and outdoor use.
Non-toxic, environmentally friendly. Maintains consistent color on hardened surfaces.
BestHard SS115
Technical summary
Category
Floorings
Surface hardener, dustproof compound for concrete.
BestHard SS115 is a one-component, active sodium silicate compound that strengthens the surface hardness of concrete, especially for subfloors and floors, increasing abrasion resistance and dust generation during concrete use.
Technical documents
Product data
| Appearance/Color | Viscous liquid/Semi-transparent. |
|---|---|
| Packing | 25liters/can ; 210l/drum, 1000l/tank. |
| Storage | In cool and dry places, at temperatures between 5°C and 30°C. |
| Shelf life | 24 months, if stored properly in original. |
| Active content | ≥ 18.5 % |
| Density | 1.15 ±0.05 kg/l |
| pH | 11.0 ± 1.0 |
| Consumption | 10 ÷ 20 m²/litre (depending on the concrete condition) |
| Dilution ratio | Undiluated |
| Permeability | 2.0 ÷ 7.0 mm (depend on surface condition). |
| Abrasion Resistance | 25 ÷ 40% increase in abrasion resistance (depend on surface condition). |
| Application temperature | Minimum: + 10°C ( above dew point temperature of 5°C) Maximum: + 40°C Relative humidity: ≤ 80% |
Applications
Industrial factory floors, warehouses, garages, parking lots, ...places requiring high abrasion resistance and dust-free concrete surfaces.
Advantages
Pre-mixed, one-component, no further mixing required, easy to use.
High penetration, strong activity.
Significantly increases hardness, abrasion resistance, prevents dust generation on concrete surfaces.
Enhances cleaning ability and prevents contamination of concrete surfaces.
Colorless, odorless, does not alter the color of the concrete surface.
Suitable for indoor and outdoor use.
Non-toxic, environmentally friendly. Maintains consistent color on hardened surfaces.
Application instruction
SURFACE PREPARATION:
Concrete surfaces must be thoroughly cleaned of contaminants such as dust, oil, grease, paint, old coatings, and curing compounds using appropriate tools and equipment.
To facilitate deep penetration, the concrete should be dried to a suitable moisture level (≤ 8%).
APPLICATION PROCEDURE:
Use a roller or low-pressure spray to evenly apply the material onto the concrete surface at an appropriate coverage rate (depending on the condition of the substrate).
After approximately 30 minutes (when the material begins to gel), use a clean water spray to evenly apply a sufficient amount of water to re-disperse the remaining material on the surface (using a brush or a floor scrubbing machine with bristle brushes).
Once the surface begins to dry again, rinse thoroughly with clean water and dry using a cloth or a wet vacuum.
If surface polishing is required, use BestSlick G85 polishing compound to enhance the aesthetic appearance of the concrete surface.
CLEANING:
Clean tools and equipment with clean water immediately after application and before the material cures.
SAFETY:
The product is alkaline and may cause irritation to sensitive skin upon prolonged contact. Protective gloves, masks, and safety goggles are recommended during application.
In case of contact with eyes, nose, mouth, etc., rinse immediately with plenty of clean water and seek medical attention at the nearest healthcare facility.
BestHard SS115 is a one-component, active sodium silicate compound that strengthens the surface hardness of concrete, especially for subfloors and floors, increasing abrasion resistance and dust generation during concrete use.