BestHard MA153
Premixed dry-shake floor hardener, super hard aggregate
Advantages:
Ready-mixed and easy to use, high quality and consistent.
High abrasion resistance.
Greatly reduces surface dusting.
Greatly increases impact resistance.
Increases resistance to oils and greases.
Greatly increases the gloss of the floor surface.
BestHard MA153
Technical summary
Category
Floorings
Premixed dry-shake floor hardener, super hard aggregate
Technical documents
Product data
| Composition | Cement, synthetic aggregates, additives. | ||||||
|---|---|---|---|---|---|---|---|
| State | Dry powder. | ||||||
| Color | Gray or green. | ||||||
| Coverage | ~ 5 kg/m² (may be higher for specific cases). | ||||||
| Packaging | 25 kg/bag. | ||||||
| Storage | In a cool, dry place at an ambient temperature of 5°C - 35°C. | ||||||
| Shelf life | 12 months from the date of manufacture. | ||||||
| Aggregate hardness (Mohs scale) | ≥ 9. | ||||||
| Compressive strength | ≥ 70 N/mm². | ||||||
| Chemical resistance | Once cured, BestHard MA153 becomes stone-hard, forming a dense surface with increased resistance to oils and greases. However, like other cement-based products, it has limitations in chemical resistance. | ||||||
| Time before service |
|
Applications
BestHard MA153 is used to increase the surface hardness of concrete floors, slabs and panels in order to improve abrasion resistance, prevent scratching and reduce surface dusting during use.
BestHard MA153 is suitable for floor surfaces subject to severe abrasion that require special hardness, such as:
Warehouse and factory floors.
Garages, parking lots and traffic lanes.
Docks, aircraft hangars, etc.
Advantages
Ready-mixed and easy to use, high quality and consistent.
High abrasion resistance.
Greatly reduces surface dusting.
Greatly increases impact resistance.
Increases resistance to oils and greases.
Greatly increases the gloss of the floor surface.
Application instruction
Surface preparation:
The designed concrete must have technical properties suitable for the intended use. During concrete placement, vibration and surface leveling must be performed correctly.
Application:
BestHard MA153 should be applied by hand in two layers. Typically about 2/3 of the BestHard MA153 is used for the first layer and the remainder for the second.
As soon as the bleed water on the concrete surface begins to dry and the concrete becomes plastic (before initial set), carry out a preliminary float to level the surface and minimize cement mortar contaminating the BestHard MA153 surface later.
After preliminary floating, spread the first layer evenly onto the concrete. Wait until BestHard MA153 has absorbed enough moisture from the concrete and darkened, the concrete reaches the required plastic consistency and does not sink deeply, then use a low-speed power float with the blade at a minimal tilt to press the BestHard MA153 powder into the concrete surface until an even wet mortar layer appears. Apply BestHard MA153 first in fast-drying areas such as column bases, wall bases, doorways and windows, etc.
Apply the second layer immediately after floating the previous one. However, top up any areas missed in the first layer to ensure the surface is fully covered and uniform in color. Floating is carried out as for the first layer, adjusting the rotation speed and blade tilt as appropriate.
Polishing:
For high gloss, increase the blade tilt appropriately and float at a higher rotation speed.
Color uniformity, gloss and mechanical properties depend heavily on the application process. Following the proper procedure gives the best results.
Curing:
Immediately after application, carry out curing to prevent early water loss that causes surface cracking. Use a BestCure product for curing to avoid cracking and surface staining, especially for colored BestHard MA153.
Cleaning:
Clean tools and equipment with clean water and soap immediately after finishing and before the material cures. Once cured, clean only by suitable mechanical means.
Safety guidance:
The material is alkaline and may cause skin irritation on direct contact. Wear rubber gloves, safety goggles and a mask during application.
If the product splashes into the eyes, rinse with plenty of clean water several times and go to the nearest medical facility for timely and proper treatment.